www.imoc.co.uk

For sale my car looking for in and around £4250

heres advert at pistonheads...

http://www.pistonheads.com/sales/918974.htm

MR2 TURBO REV 3 I dunno what to do and need all help can get from you guys... Car went for rebuild came back and speedo needle was bouncing about up and down frantically.... so i read up went to local scrappers and got an st205 celica speedo sender from the gearbox and the plug from the loom which c...

Hi

Im thinking of taking advantage of my forged pistons and upgraded engine parts by increasing boost...

The two methods i believe of doing this are by uprated actuator probably 1.0 bar or boost controller

which is best opinions needed and advice on best of each of these...

The lsd just took time to bed in if thats the right word doesnt make ne noise at all now

When my rev 3 turbo is idling the revs move just a wee tad and i mean a wee tad from say 1000 to 1050 rpm and theres a noticable wee spit misfire...

any ideas where to start to remove this issue

Could anyone tell me where you get mounting flanges at good price as thinking of bidding on a sard dump valve for car but it doesnt have flange for mr2 or any ideas?

There aint one connected at min not sure about before as previous owner could have connected one and disconnected??

Hi all could someone help me with my REV 3 electronic speedo... as im at my wits end wit this car... My car speedo was working then started jumping about when I accelerated hard... now the speedo doesnt work and after playing about with the clocks it now sits at 60mph when the power is switched on i...

How you know the difference looking at clocks

Bought a speedo there as think mine is bin material.. my car is rev 3 question is, is there a difference between rev 1 2 and 3 speedos? also the speedo which arrived had converter on back with 3 wires connected to clocks but had a wire for speed signal which knows goes to purple wire in loom but the...

yea is a turbo... i tried removin the chip in behind clocks and rewiring original wiring still the speedo dont work...

im also getting error 42 and engine light on now

Head gasket was 1.2mm thick not sure dont think they were as they are forged pistons

Spec is as follows... 1995 rev 3 turbo... running standard boost gutted cat fujitsubo exhaust with 3 inch pipe cat back standard turbo that i know off engine is bored .5 and running wiseco forged pistons hks metal head gasket acl race bearings car is running intercooler fan constand and radiator fan...

My speedo doesnt work and cannt figure out why, ive done following... 1.) Replaced the whole gearbox speed sensor with a 2nd hand unit 2.) Rewired the loom at back with new adaptor to gearbox sensor 3.) I put positive end of volt meter to speed signal wire(purple with silver trace wire) at back of c...

Hi all,

I remember seeing a pic of a white mr2 on red standard rims im thinking of doing the same to my winter wheels painting them red anyone have a pic of this mr2????

Hi all me again, I was wondering the boost on my rev 3 seems to come in full at 4500 in 3rd gear etc which to me is very late... the idle sits at 1100 rpm is this linked also what should it be kicking in at... the car is running standard boost, upgraded pistons and gutted cat... ne ideas y it is boo...

Lads, ur prob sick of seeing me askin questions...

I have sourced my speedo not working to the gearbox side of things but have a problem... where the speedo cable connects (3 wires) it seems to sillicon round it wanna c a pic of other peoples so know wot it shud look like

I have searched and cannt get a definate answer for which gearbox oil to use for my two way lsd... mt-90 redline seems to crop up everywhere but theres no friction modifier in it so thats nt an option?? Also i have read you dont use synthetic oils on Kazz website so what type of oil am i after? Read...

Got small issue wanna resolve car when sitting idling is reving ever so slightly up and down betwen 1100 and 1000 rpm how can i resolve this issue so the revs stay constant...

Aw just got car back after gettin engine rebuilt due to cracked block, nw theres a weird noise from diff/lsd think... It occurs when i pull out of a junction in 1st gear sorta a grinding noise then disappears when get up to speed... my mechanic said its a good lsd very tight etc.... im worried its t...