





October 1999.


Toyota MR-S MR2 as its successor.


The speed with which the difference between the turbo and supercharged MR2, MR-S sports car was a lightweight stressed.



However, since fiscal 2000 have been entered for the race GT Championship Series MR-S is very aggressive in silhouette,

Is so cool-looking fast was the car.



The same year in August 2000, from customized Moderisuta Toyota dealer, GT championship race car in the motif

MR-S Custom Car



Both before and after the retrofit on one side and 3cm Burisutafenda swell, TRD MR-S was a charity even for Raitochun laden parts.


However, its design is a replica of feeling is even called the tyranny.



Autobacs custom car development project, not motif




Regulation of the GT championship race car, commercial vehicle from a width of 10cm were allowed to extend the modification.


Upstream sector of races Toyota, TRD designs attached to cooperate more with one side of 5cm wide, including the fender panel,

GT body parts to produce a faithful copy of a racing car championship run.


MR-S Racing finally completed as a replica of the real.



And January 12, 2001, Tokyo Auto Salon.


Toyota MR-S replica racer from Autobacs Seven Co.














October 1999.


Toyota MR-S MR2 as its successor.


The speed with which the difference between the turbo and supercharged MR2, MR-S sports car was a lightweight stressed.



However, since fiscal 2000 have been entered for the race GT Championship Series MR-S is very aggressive in silhouette,

Is so cool-looking fast was the car.



The same year in August 2000, from customized Moderisuta Toyota dealer, GT championship race car in the motif

MR-S Custom Car



Both before and after the retrofit on one side and 3cm Burisutafenda swell, TRD MR-S was a charity even for Raitochun laden parts.


However, its design is a replica of feeling is even called the tyranny.



Autobacs custom car development project, not motif




Regulation of the GT championship race car, commercial vehicle from a width of 10cm were allowed to extend the modification.


Upstream sector of races Toyota, TRD designs attached to cooperate more with one side of 5cm wide, including the fender panel,

GT body parts to produce a faithful copy of a racing car championship run.


MR-S Racing finally completed as a replica of the real.



And January 12, 2001, Tokyo Auto Salon.


Toyota MR-S replica racer from Autobacs Seven Co.






Mono Craft GT-300 is refurbished from the MR-S CAR Konpuritoka to register on the size and number three,

MR-S in併売on hand to fit them with the kit, limited production of 100 sets were sold.



Burisutafendapaneru the sides, around bumper, side skirts left and right Innafendakitto,

Fuel lid only, the full set of the emblem, 1 kit price is 400,000 cars.



Built-in panel of more than half of replacement vehicles, with an extensive refurbishment work to painting.


The trial assembly made of FRP panels, according to Chile's panel issued a surface, the paint work is nearly half of the car,

Starting point in about two weeks, and cost around 40 million take.



This MR-S from the full width of 1,690 mm to 1,790 mm wider.


Because the limit is 1,700 mm in size No.




Takashi, based on actual measurements, so the actual width, 1,790 mm and has Datsu Dattari 1,800 mm.



If I want to keep everything in Tsuraichi wider wheel size.


My GT-300 Star Craft made things work as a set of wheels and tires to recommend the S1 prepared in 35 million yen.



Konpuritoka the simplest B-only edition of the top five with a hard-drive until wheel speed manual

Three new car prices vehicle body structure changed number






Report Report of Hilo car garage.


NEXT



monocraft GT-300 Designed by TRD





Owner: Cooperation shooting Araki Toshikazu: Gunma Nettsutoyota Tomioka Iti and stores only

Photo







Approximately one year over three sold out in January 2002.



Response to the voice of Angkor, which was renewed in 2003 altered the design slightly in January,

Was released from the company as a regular item.


Being reviewed and the usability of the strength of the side skirts and fuel lid,

And inner fender and fender arch design was baked in the shapes and commercial vehicles.



Things made by hand in terms of design, the model is the least



This late model 2007 and one that all production is finished in January.














