Does the FTO has got the same fitment as my Mk2 MR2? The seller has mentioned about the fitment.
..(The PCD is 114.3 and the offset on the front is 16 x 7 OJJ 5 1/2 and the rear is 16 x 8 6 1/4 inch.)Does it make sense?
Cheers!
Dom
Wheel fitment question
Moderators: IMOC Moderators, IMOC Committee Members
-
TheRed2
Wheel fitment question
I am looking at a set of 16" rims on ebay which were wearing by a FTO before.
Does the FTO has got the same fitment as my Mk2 MR2? The seller has mentioned about the fitment...
(The PCD is 114.3 and the offset on the front is 16 x 7 OJJ 5 1/2 and the rear is 16 x 8 6 1/4 inch.)
Does it make sense?
Cheers!
Dom
Does the FTO has got the same fitment as my Mk2 MR2? The seller has mentioned about the fitment.
..(The PCD is 114.3 and the offset on the front is 16 x 7 OJJ 5 1/2 and the rear is 16 x 8 6 1/4 inch.)Does it make sense?
Cheers!
Dom
Re: Wheel fitment question
they sound ok, not sure about the offset - you want ET35-ET45 (you can go lower with arch work)
standard wheels are ET45 not sure if thats too high or not as the wheels are both 1 inch wider than standard
whats the centre bore size?
Steve
- you want ET35-ET45 (you can go lower with arch work)standard wheels are ET45 not sure if thats too high or not as the wheels are both 1 inch wider than standard
whats the centre bore size?
Steve
-
TheRed2
Re: Wheel fitment question
steve wrote:they sound ok, not sure about the offset
standard wheels are ET45 not sure if thats too high or not as the wheels are both 1 inch wider than standard
whats the centre bore size?
Steve
Thx Steve! The seller seems not knowing his product quite well.
I will try to ask him though. BTW, Where are you about in KENT? I saw your car at last bluewater meet, very nice motor! Like your rims!
=D> Dom
-
Andy Jones
- Posts: 3271
- Joined: Tue Dec 14, 2004 12:22 pm
- Location: Oldham
- Contact:
Re: Wheel fitment question
Ask the seller to see if he can see ET(followed by 2 digits) stamped anywhere on the wheel this will verify the offset so you can be certain they'll fit the 2 without any rubbing.
The PCD is the same and FTO's have a centre bore of 67.1 so you'll just need some 67.1-60.1mm spigot rings.
The PCD is the same and FTO's have a centre bore of 67.1 so you'll just need some 67.1-60.1mm spigot rings.
Re: Wheel fitment question
TheRed2 wrote:
Thx Steve! The seller seems not knowing his product quite well.
BTW, Where are you about in KENT? I saw your car at last bluewater meet, very nice motor! Like your rims!
Dom
no problem
cheers mate, i'm in gravesend.
should be at bluewater again next tuesday - come and say hi if your going 
Steve
-
TheRed2
Re: Wheel fitment question
The seller has posted me a reply. He could only find 5H DB written on the wheels! 
Could somebody tell me what is that? 
He could only find 5H DB written on the wheels! Could somebody tell me what is that?
Re: Wheel fitment question
TheRed2 wrote:The seller has posted me a reply.
Could somebody tell me what is that?
no idea
](./images/smilies/eusa_wall.gif "Brick wall"){kind=small}
found this though http://mivec.co.uk/performancedata/
Wheel offsets Width 6.5 Offset
depends if the wheels are standard or not i suppose
-
TheRed2
Re: Wheel fitment question
They were a set of aftermarket wheels. but thx for your data! =D>
Really appreciate! If I could turn up at the next Bluewater meet, I must come and greet you mate! 
Dom
but thx for your data! =D> Really appreciate! If I could turn up at the next Bluewater meet, I must come and greet you mate!
Dom