Essex RR II Dyno Table

[poyntesm]

OK..I will do it so.

Will not be done for a week or two so not much use for this one...but will be done for the next one. Think I will do the same for 1/4 mile times.

[ginga]

240rwhp 254lbft

[CosmosblueMR2]

240rwhp 254lbft

almost identicle to me and Bry ! - what boost you running Dave ?

[ginga]

240rwhp 254lbft

almost identicle to me and Bry ! - what boost you running Dave ?

Just a gnats over 16psi, I'm a happy lad with that, I was 10lb down on torque from last time but could be down to the clutch slipping like a pig, Just watched the vid and you can hear it going

[jimGTS]

everyone seems to be 20 up on last time, all a bit strange, lol.

[Mark Edwards]

I got 288rwhp and 270.9lb/ft

So close to the magic 300 !! are you happy with that?? what you were expecting?? what boost did you run??

Cheers
KiwiMR2

I was actually expecting it to go over the 300 mark, around 310 - 315 was the idea, but happy overall, especially with the 12.4 at the strip the day before.

[Bry]

everyone seems to be 20 up on last time, all a bit strange, lol.

I was 12bhp at the wheels up compared to last time but 6ft/lbs torque down,which makes sense as I ran less boost this time (1.15 as opposed to 1.2bar)which is why my torque was slightly less and I put the power rise down to the Rogue system fans doing a great job Power fc will be going on any day now then it's off to be mapped,hopefully I can get 260rwhp

[3sgte]

255 rwhp only 234 lb/ft
but i was only spiking 1 bar and holding 0.9 hopefully getting apexi avc-r this week to sort out the boost (my hks should be up for holding 1.2 bar)
although max power 329@fly) at 7500 rpm so the turbo defo doesnt fade at high revs

[Pete J]

I had 122 bhp at the wheels and 146 lbft

James D had 222 bhp at the wheels from his totally stock rev 3 =D>

[Pitcher]

240bhp at the wheels and 298.4 lbft Torque!!! who has the highest torque???

Peaked at 1.38bar but AVC-R cut it back and was holding it about 1.12bar, wanted it to hold 1.20, so a few more adjustments are needed....

James

[Rory]

240bhp at the wheels and 298.4 lbft Torque!!! who has the highest torque???

Thats a pretty good result for a high mileage 2! Well done.

Did your torque hold at that though or peak then drop off fast? I noticed that I had gained about 50bhp but lost 10LBft of torque since my last lot of mods. This doesnt matter though because my graph was much smoother. If you look at my first graph (basic mods) youll notice my torque peaks then drops. The second graph is from this weekend with all my engine mods done. (The graphs below are not on the same scale)




Rory

[Pitcher]

Here is my graph....



the boost seemed to drop off a bit, need to adjust the AVC-R to try and hold it better.

James

[Mark Edwards]

Here's mine.

[Chelle_Hutch]

Hi Everyone
Sorry i'm a bit late but its been a bit hectic!

I will shortly put together a list of everyones BHP and torque figures in a post, unfortunatly i only have fly figures not wheel figures. Hopefully the write up for the day will be sent to J Tuner tomorrow to appear in mag asap.

Thanks for a fantastic day =D>

Chelle.

[CosmosblueMR2]

Hi Everyone
Sorry i'm a bit late but its been a bit hectic!

I will shortly put together a list of everyones BHP and torque figures in a post, unfortunatly i only have BHP and not fly figures. Hopefully the write up for the day will be sent to J Tuner tomorrow to appear in mag asap.

Thanks for a fantastic day =D>

Chelle.

Nice one Chelle ! =D>
was wondering where you had got to actually

RWHP figs are best to be honest anyway (more accurate) - so will be good to see ALL the results listed.

good effort - and glad you enjoyed the day... we had a nice number of car's out in the end.. still not as many as were "interested"... where do these people go ??!!

Essex RRday III will be next year peeps - thinking about a nice dry cold day in April/May - after everyone's winter mods

[3sgte]

258rwhp 234 ft/lbs at 11.5psi