www.imoc.co.uk

Hi,
We've been thru this.
Do you have a Front Mount cinquechento (?) rad or similar?
And an EWP?

Hi, If we wanted to convert our 3S-GTE to a "stronger" block design, one of the options is to get a Camry 2.2 engine (say a 1998 car). But has anyone actually done this? Can anyone shed some light on the list of mods needed to achieve this? Is it a taller block? Will all the ancilliaries a...

Guys, I can add a bit more detail to Mitch's post above as I am responsible for the engine build + spec etc...! Its highly modified, custom chargecooler, DTA EMS, forged engine etc etc and has been fine until we raised the rpm/boost etc following running in. I am concerned that with all the modifica...

Received my kit today for the rears. Hopefully attempt this job the weekend with new discs + pads. Many Thanks ANT!

Hi Ant,
jannerboy - REAR ONLY KIT - Disclaimer Read & Agreed

Add me to the list!!!
cheers,

mr2mitch - REAR ONLY - Disclaimer Read & Agreed

Hopefully you have enough people now?

guys, would any of you know the part number for the Drivers Side (offside) gearbox oil seal (from their EPC) please? I have looked at the EPC online and it is not clear which is the correct part number...normally no issues as the EPC online is ace! Its the seal that runs on the "half shaft"...

hi allan,

the picture is the same for both the epcs at this site.
the manifold part numbers are the same...and its the T-VIS design Rev 2.

john

allan, right i have a newer multi-disk version installed... i have the CDs for the Euro and the Jap versions lined up and it seems to all work ok...havn't installed the Gen versions yet... but i can't get to 1994 on mr2 turbo info... perhaps u could do me a favour? could you tell me the full part nu...

allan, my rev 2 vin and changing the year didn't work. i have tried inputing different Catalog Codes and that didn't work... it can't be that difficult... #-o why is the later mr2 turbo not in the list of catalog codes??? it only lists MR2 8912-9506 (and others) covering the whole range of MR2s... H...

Si,
I realised in the first pic, the bracket is the wrong way around. Also the clutch slave cylinder needed to be fitted under it. so that one is sorted now.

the other one is for the stereo...could be as i can't see where it goes!

thanks,

Hi, i've got the 2 disk version of the EPC installed ok. I am trying to get to info for a Rev 3 1994 on MR2 turbo...but for the life of me i cannot seem to enter the right info!!! :oops: We've just put a rev 3 motor replacing the rev 2 so i wanted to get at all the engine details etc...i don't have ...

hi, i'm re-building the old '92 MR2 turbo at the moment. I've got a couple of parts left over and either not sure which way round they fit or don't know where they go ! #-o looked at pics and still no joy! http://img9.imageshack.us/img9/4558/16032009234.th.jpg this is the engine mount at the back. t...

steve, nice one. thought i'd been banned
i'll just sit here in the corner and get on with me work now then

Guys,
my messages stay in the outbox and do not get sent...any reason for this...
John

Guys, I wonder if u can help. We replaced the gearbox and clutch on the Rev 2 Turbo with an OS Giken Twin Plate clutch (new release bearing) and gearbox from a Rev 3... All went to plan. First time with engine on tried to get it into gear...won't go... We assembled the clutch according to manual. Th...

Hi, We are looking at our options for NOS on a 92 turbo. We've done some mods and found intakes temps can rocket "on boost" quite quickly... Does anyone have pictures of their install? it seems the bottle could go in the boot and plumb thru the rear wall? from our searches these kiddies se...

Recaro profi spgs here. About 6.8kgs each...they would look good...

How heavy are the standard seats?

What model recaro's are in your motor skipp123? I see your in Max Power this week too...

Right the front seats need to be either repaired or replaced...but we were thinking maybe its time to get the weight down a little and replace the seats with some lightweight options...

what is currently peoples favourite lightweight seat options that are direct replacements???

cheers, john

Hi Brian,

thanks mate, I'll give them a call.
We'll sort the ride height out first.

John.