www.imoc.co.uk

Sourced an alternative due to lack of response Why did you not send a pm ? i for one always forget to look for replies to my previous threads/posts and rely on them :wink: I sent many, unfortunately communication dried up after asking for pics- no dramas though as I have already said I sourced anot...

Sourced an alternative due to lack of response Why did you not send a pm ? i for one always forget to look for replies to my previous threads/posts and rely on them :wink: I sent many, unfortunately communication dried up after asking for pics- no dramas though as I have already said I sourced anot...

Sourced an alternative due to lack of response

Interested in this pending more pictures please!

Id definitely be up for one of these if another group buy comes up!

I have 2 mr2's, a v6 rev3 and a rev4 na,trying to find ecu pinouts for both and having no joy :( on the rev4 I had fault code 41 before and replaced the tps and ecu,no joy so replaced the wiring between,now got code 22!water temp sensor! If anyone has the ecu pinouts for other cars it would be massi...

I have a tubby gearbox but it had the non abs shafts, can I just put abs shafts in it or do I need to have the inner cv joints to the box and fit those to a set of abs driveshafts?
Any advice would be great! It's going into my rev3na converted v6

MartinF wrote:Why didn't you just buy the new friction face? That's one of the benefits of the Fidanza flywheel

only cost me £20 for it to be surfaced...otherwise I definitely would have,stupidly assumedthe studs were the same in the standard flywheel but it definitely isnt!haha

I have had a fidanza flywheel refaced and they had to extract the studs out to do so,now they have a big hole in the middle...can you get replacements for them or am I better off getting a machine shop to make some up?

Hiya!Iknow you can only get the rubbish small ppanel from MR T but what alternatives do I have?seem to remember fiesta van sills? And advise would be great guys!my v6 project needs new sills (they have started so want to rip out and replace)

Pm'd!

Cheers for the advise so far guys! Have sent you a pm regarding the plastigauges!

Thats a great help! Tbh the engine was fine when I removed it-you could just about hear the tappets from cold (faintly) but I have replaced pretty much everything else on the car so it would be nice to have a basically brand new engine:). What I don't understand is how by using aftermarket bearings ...

Says something about 3 different sizes I thought-these markings on the bearings will they be embossed or will it be quite hard to see? Appreciate the advise so far guys:)

Have you got the BGB- it's all explained in there, and if you're planning to do it properly you probably want to get your head into the book! There are different standard toyota bearing sizes, but if you use after market bearings (eg ACL) they just have one "standard" size...fit them and ...

I am in the process of rebuilding a spare engine I have,being honest I have not done a block rebuild before and looking for advise on how to make sure I get the correct bearings for the crank and the conrods-been told about some sort of numbering system on the caps to help identify which standard be...

Where can I get these chris wilson pads? Wouldnt mind the carbotechs if they aren't rediculously expensive
Cheers for the advice so far guys:)

woz_106 wrote:What do you use the car for? road, track mixture of both?

daily driver but have a "spirited" driving style!haha

I am using ebc drilled and grooved discs, pads need changing just wondering what would be the best ones to go for?Currently using ebc ultimax pads
thanks in advance
matt

I have asked about progress, unfortunately he is very busy atm but has informed me that he will keep me upto date with his progress on the project