Includes:
- Controller (set boost pressure injection starts, and pressure where full injection volume is reached)
- Pump
- Large water/ meth plastic container with low level sensor
- Assortment of nozzles (from memory small/ med/ large)
- Some pipework and fittings
£179 + postage, or collected from near Gloucester.
Photos to follow
[FINALIZED] AEM Water/ Meth injection kit
Moderators: IMOC Moderators, IMOC Committee Members
Re: [FINALIZED] AEM Water/ Meth injection kit
Interested.. I take it it's pretty much complete bar some pipe work?
EX MR2 owner, currently on a '00 Honda CBR600 Follow me on Instagram @c35rob
Re: [FINALIZED] AEM Water/ Meth injection kit
Exactly that mate, and I've got some other bits I was going to use with it which you might like as well:
- One way valve/ solenoid
- Additional large and small nozzles (small is suitable fro pre-compressor injection, and the large in tandem injecting pre-TB)
- Lots of pipework
- Ali bracket to place a nozzle in front of the compressor wheel (need to check diameter- but I think it is to fit a 4" compressor inlet)
- A large drum of clinical quality methanol (5 gallon from memory)
Need to dig out how much I paid for that lot though, but you could have it for a decent price
- One way valve/ solenoid
- Additional large and small nozzles (small is suitable fro pre-compressor injection, and the large in tandem injecting pre-TB)
- Lots of pipework
- Ali bracket to place a nozzle in front of the compressor wheel (need to check diameter- but I think it is to fit a 4" compressor inlet)
- A large drum of clinical quality methanol (5 gallon from memory)
Need to dig out how much I paid for that lot though, but you could have it for a decent price
Re: [FINALIZED] AEM Water/ Meth injection kit
My compressor housing is a 3" inlet unfortunately, pm me a price and I'll make a decision
EX MR2 owner, currently on a '00 Honda CBR600 Follow me on Instagram @c35rob
-
- Posts: 635
- Joined: Thu Dec 16, 2004 10:52 pm
- Location: Sutton Coldfield
Re: [FINALIZED] AEM Water/ Meth injection kit
HI Ashley,
If Rob decides against the kit, I'll take it off your hands
Cheers,
Mark
If Rob decides against the kit, I'll take it off your hands
Cheers,
Mark
Re: [FINALIZED] AEM Water/ Meth injection kit
ar$e!
If not, i'll have it
If not, i'll have it
Re: [FINALIZED] AEM Water/ Meth injection kit
Hands off! It's mine..
EX MR2 owner, currently on a '00 Honda CBR600 Follow me on Instagram @c35rob
Re: [FINALIZED] AEM Water/ Meth injection kit
Good buy Rob
Would of had this off Ash otherwise.
Would of had this off Ash otherwise.
Re: [FINALIZED] AEM Water/ Meth injection kit
It's Rob's (unless he changes his mind), but I'm sorry- pictures are going to have to wait until tomorrow- it's too hot in the loft to go up and get it all tonight...sorry
Re: [FINALIZED] AEM Water/ Meth injection kit
Pictures!
The basic kit £179 (pictured below 2 of the 3 AEM nozzles, the third will be included)
Then Coolingmist accessories:
180cc nozzle
760cc nozzle
Bracket for 4" diameter compressor inlet for pre-compressor injection
3m tubing
Solenoid, T-junction and 2 push fit fittings
Individually:
Nozzles £10
T-Junction £8
Quick connect fittings £7
Solenoid £45
Tube £10
AEM kit £179
Pre-compressor bracket £10
Rob's got first refusal
The basic kit £179 (pictured below 2 of the 3 AEM nozzles, the third will be included)
Then Coolingmist accessories:
180cc nozzle
760cc nozzle
Bracket for 4" diameter compressor inlet for pre-compressor injection
3m tubing
Solenoid, T-junction and 2 push fit fittings
Individually:
Nozzles £10
T-Junction £8
Quick connect fittings £7
Solenoid £45
Tube £10
AEM kit £179
Pre-compressor bracket £10
Rob's got first refusal
Re: [FINALIZED] AEM Water/ Meth injection kit
this still for sale mate?
-
- Posts: 6071
- Joined: Wed Dec 15, 2004 10:16 am
Re: [FINALIZED] AEM Water/ Meth injection kit
This Sale has been completed. The Buyer was C35Rob