Following on from another thread in the wanted section ,
I went over to the company in question ,and came away with these rams ,
As you can see the body is thinner than the normally available struts ,so they should sit better in the bonnet bay, to solve the issue people have had in the past with the bonnet being raised slightly
I also bought a shorter one for the engine bay ,just need some brackets now ,possibly from E-Bay (unless anyone knows somewhere else that sells them?)
http://www.ebay.co.uk/itm/Seat-belt-bra ... 336addc8ab
and as you can see they work out cheaper as well
I previously filled in a request on their website and the company emailed me back with these prices ,
I wasn't sure on the pressure required ,so priced up adjustable strength rams (and asked about bulk discount)
£18.80 each
6+ £17.86
20+ £15.04
50+ £13.16
After chatting with the staff there today.i bought fixed strength rams @ £17.49 + vat
so if enough of you buy them together they can be even cheaper ?
Quality seems good ,and ill be fitting them at the weekend,so ill post up again
[Mk2] [Generic] Bonnet and engine bay hydraulic struts
Moderators: IMOC Moderators, IMOC Committee Members
-
- Posts: 2726
- Joined: Mon Jun 25, 2007 9:47 pm
- Location: Coalville, Leics
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
Could a proper group buy get started for these Trevor? I would be interested and it looks like that other group buy has died a death.
Dans Modified MR2 Turbo >>> http://www.imoc.co.uk/forums/garage.php ... e&CID=2727
-
- Posts: 264
- Joined: Sun Jan 10, 2010 3:55 pm
- Location: Cowes, Isle of Wight
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
Id definatly be interested in an engine bay one! Refuse to replace the stay clip for the 3rd time
Rev 1 NA to Turbo conversion!
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
I'm keen for these aswell, its a job I keep putting off because my engine lid either stays closed for long periods of time or open for long periods of time!
I saw them on ebay but you had to get them from Canada I think so something I could buy in the UK would get my vote.
I saw them on ebay but you had to get them from Canada I think so something I could buy in the UK would get my vote.
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
timlowthian wrote:Id definatly be interested in an engine bay one! Refuse to replace the stay clip for the 3rd time
What he said! cost me like £10 for the last one.
I'm in
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
I fitted the bonnet rams this morning ,and all seems good ,i cant see any increase in bonnet height after fitment ? .
i fitted them with the ram pointing down ,and then changed them over to the other way round ,in my opinion they are better this way round
on the old type of ram people had to file flat the ball fittings ,due to them catching ,ill give it a while and have another look at them ,to see if this needs doing to these ,cant tell at present everything is wet
Hard to get a picture from the exact same angle ,but they are good enough for me
Before fitment
Ram pointing down
Ram pointing up
After fitment (you can just see the shiny ends)
Now to try and fit the rear one
i fitted them with the ram pointing down ,and then changed them over to the other way round ,in my opinion they are better this way round
on the old type of ram people had to file flat the ball fittings ,due to them catching ,ill give it a while and have another look at them ,to see if this needs doing to these ,cant tell at present everything is wet
Hard to get a picture from the exact same angle ,but they are good enough for me
Before fitment
Ram pointing down
Ram pointing up
After fitment (you can just see the shiny ends)
Now to try and fit the rear one
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
D4N_V_U wrote:Could a proper group buy get started for these Trevor? I would be interested and it looks like that other group buy has died a death.
I'm not in a position to lay out the money for a group buy ,i dont have a credit card any-more to offset the cost until people pay,
But i can collect them and distribute out to people, if someone wants to set one up ,
If someone does set one up ,ill provide the details as to what is needed to be bought from the website
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
im interested in bonnet and engine lid
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
yep count me in i'd like both sets please.
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
interested in engine lid one
-
- IMOC Affiliated Trackday Organiser
- Posts: 10506
- Joined: Tue Jan 25, 2005 9:49 am
- Location: South Yorkshire
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
I've had these manufactured and in stock for years. I'll check what i've got when i'm in the workshop next week.
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
Peter Gidden - SBITS wrote:I've had these manufactured and in stock for years. I'll check what i've got when i'm in the workshop next week.
Put me down for a rear one if you still have one
-
- Posts: 264
- Joined: Sun Jan 10, 2010 3:55 pm
- Location: Cowes, Isle of Wight
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
Peter Gidden - SBITS wrote:I've had these manufactured and in stock for years. I'll check what i've got when i'm in the workshop next week.
Id be interested to know how much an engine bay one is? Not interested in bonnet lifters hardy go in there anyway
Rev 1 NA to Turbo conversion!
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
Peter Gidden - SBITS wrote:I've had these manufactured and in stock for years. I'll check what i've got when i'm in the workshop next week.
Interested on front ones price depending
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
Whats the going rate for engine lid kits?
-
- IMOC Affiliated Trackday Organiser
- Posts: 10506
- Joined: Tue Jan 25, 2005 9:49 am
- Location: South Yorkshire
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
I'll get onto to my laser cutter later this week. Craig (RedMR2) has been onto me wanting a Group Buy, so i'll report back in a few days.
-
- Posts: 148
- Joined: Thu Sep 09, 2010 11:04 am
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
I'd be interested in both the engine bay and the front bonnet ones, sorry I couldn't get the group buy sorted. New to that and didn't know how to sort out the amount of cash that had to be put down etc...
-
- Posts: 148
- Joined: Thu Sep 09, 2010 11:04 am
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
I'd be interested in both the engine bay and the front bonnet ones, sorry I couldn't get the group buy sorted. New to that and didn't know how to sort out the amount of cash that had to be put down etc...
Re: [Mk2] [Generic] Bonnet and engine bay hydraulic struts
Peter Gidden - SBITS Posted: Mon Dec 26, 2011 10:48 am wrote:I'll get onto to my laser cutter later this week. Craig (RedMR2) has been onto me wanting a Group Buy, so i'll report back in a few days.
What's your version of "a few days"