www.imoc.co.uk Forum Index
 AlbumAlbum CalendarCalendar FAQFAQ SearchSearch MemberlistMemberlist Legal NoticeLegal Notice IMOC 1/4 Mile1/4 Mile Table Knowledge BaseKnowledge Base   RegisterRegister 
 GarageCommittee GarageGarage  SubscriptionPremium Membership  ProfileProfile   Log in to check private messagesLog in to check private messages   Log inLog in 
Calendar 
Knowledge Base 
 How to solve hesitation, missfires and flat spots 
Description Steps to solve these problems
Author Goldy Date Fri Nov 25, 2005 12:17 pm Type Text How-To

Category Engine
Viewer Comments [6 - Post your comments]
Views 27439
How to solve hesitation, missfires and flat spots
Steps to solve these problems
This comes up a lot so I thought I would do a little write up on it. Feel free to add to this if you feel I have missed something out!

Hesitation and flat spots are generally caused by poor ignition components. I have recomended things to check in the order that they are likelyest to be and the cost of replacement.

1. Check the distributer cap and rotor arm. (see separate how to for replacing them) If the contacts are heavily corroded or damaged replace them. Check for signs of oil or water in the distributer cap. Whilst you have the cap off.....

2. Check the state of the connectors on the HT leads, look for corrosion or damage to the contacts again.

3. Check the state of the ht leads in general, look for splits in the leads, kinks and check the connectors at the spark plug ends.... whilst you have the ht leads out.....

4. Check the state of the sparkplugs.... look for wear on the electrodes, damage or discolouration

5. Check the airfilter.... replace / clean if dirty

6. Check the ecu for error codes and perform an ecu reset.

If these all look ok but you still have a flat spot I suggest:

1. Replace the dizzy cap and rotor arm first (around 20 for the pair from mrT)

2. Replace the sparkplugs next (NGK's cost about 8 for 4 from unipart)

3. If the problem is still there try some injector cleaner

4. I suggest changing HT leads last of all as these don't tend to fail very often and are very expensive to replace!
  

 User comments 
Rikki: Tue Nov 29, 2005 11:38 am    

"1. Replace the dizzy cap and rotor arm first (around 20 for the pair from mrT) "

Reckon?

Rotor arm 8.18
Dist cap 40.93
HT leads 65.20

All + vat

R.
Goldy: Tue Nov 29, 2005 5:09 pm    

Depends if its uk or import, turbo or n/a

My uk n/a cost :

13.76 for dizzy cap
8.46 for rotor arm

The HT leads were however 74.64

Will deff be cheaper to get blueprint parts.
dan9: Mon Apr 03, 2006 6:35 pm    

It is worth checking the ignition timing as well, possibly before spending any money on new parts.

My mk2 N/A MR2 had one great big flat spot, all the way through the rev range. Very hesitant, hardly any acceleration, and poor fuel economy.

The timing was quite significantly retarded (about 10 degrees at idle). Correcting the timing made a huge difference to performance.

I recommend following the instructions in the excellent Knowledge Base guide.
Mike N: Sun Dec 09, 2007 2:12 pm     rev 2

What would cause a rev 2 to cut out or only run at just above tickover after 10 minutes of driving?

Thanks
monstr2: Sat Jan 23, 2010 5:23 am     vaccum leak =too many problems

DEL
Page 1 of 2 All times are GMT
Goto page 1, 2  Next 
Viewer Comments [6 - Post your comments]

Jump to:  

Powered by Knowledge Base, wGEric 2002 PHPBB.com MOD
This script (Knowledge Base - MX Addon v. 1.03e) is modified by Haplo



Powered by phpBB © 2001, 2005 phpBB Group